No Image

Multi-tools

СОДЕРЖАНИЕ
0
0 просмотров
07 февраля 2020

IF WELL-MAINTAINED, YOUR LEATHERMAN CAN LAST A LIFETIME.

CLEANING / LUBRICATION / RUST & CORROSION PREVENTION

All Leatherman products are manufactured from 100% high-grade stainless steel (exception: screw bits for the tool adapter are made of tool steel). Stainless steel is not rust proof; it is corrosion-resistant. Depending on the mix of metal alloys, stainless steels may be highly corrosion-resistant and relatively soft (like kitchen flatware), or they may be somewhat corrosion-resistant and quite hard. Our products are fabricated from the latter type, so your tool components are strong, and the knives retain a sharp cutting edge.

Depending on what your Leatherman has been exposed to, there are several cleaning methods to consider.

  • Cleaning can be done with a low viscosity oil (e.g. WD-40, Liquid Wrench, CRC 3-36), which helps force out moisture trapped in the joints.
  • Buff stained surfaces with a polishing cloth or non-metallic abrasive (e.g., Scotchbrite pad or soft bristle brush).
  • For pivoting or wear areas, use a PTFE / Teflon-based lubricant to make your tool function as smoothly as possible.
  • If debris or sticky substances have accumulated between the blades, your Leatherman may also be cleaned in a mild solution of detergent and water.
  • To remove tar and similar substances, clean your Leatherman with turpentine or other mineral spirits. Warning: acetone or brake cleaners may damage plastic components.
  • Corrosion can occur in the absence of proper maintenance. Your Leatherman product should be cleaned, dried and re-lubricated periodically to inhibit rust and corrosion. This is especially true if your Leatherman has been exposed to salt water or marine environments. If so, rinse in fresh water, dry, and lubricate it with a light oil.

Blade Sharpening

Leatherman knife blades may be straight-edged, serrated, or both. Sharpening methods vary depending on the type of knife in your Leatherman product (note: serrated edges should not be sharpened in the same manner as straight edges).

  • Straight-edged blades can be sharpened using any standard equipment, including whetstones, rods, and various kits.
  • Leatherman’s standard sharpening angle for plain edge blade sections is 32° (16° per side). Serrated blade sections are sharpened to 20° (one sided).
  • Serrated blades require a sharpening system specifically designed to accommodate serrated edges in order to maintain the curvature of the serrations. Sharpen serrated blades only on the edged side. Sharpening the flat (back) side of the blade will cause the serrations to wear away, reducing the blade’s effectiveness.

Wearable Care

The Tread is comprised of 3 main parts, all of them being some type of stainless steel alloy:

  • Screw: SS410
  • Connector: SS420
  • Link: SS17-4

The key to understanding “stainless steel” is to break the word apart to “stain” and “less”. They all still contain iron (Fe) and can therefore oxidize in certain environments. The human body is a highly saline environment that accelerates corrosion. The Stainless steel alloys vary based on their intended use, with some oxidizing less than others. Leatherman chose the above alloys based on a compromise between process constraints and performance.

For your wearable you should clean salt off daily, maybe using a toothbrush to get into all the spots. However, if that is not enough to slow corrosion you may need to do some preventive coating like oil. You may have to experiment with oils that you are comfortable putting in contact with your skin. You may need to consult a dermatologist.

Список источников

  • www.leatherman.com

Похожие статьи

Комментировать
0
0 просмотров

Если Вам нравятся статьи, подпишитесь на наш канал в Яндекс Дзене, чтобы не пропустить свежие публикации. Вы с нами?

Adblock
detector